Neo Baby Car Seat

 Osann Neo 360 Manual

• This Neo baby car seat is applicable for children in the ECE group 0/ 1/ 2/ 3. Weight range 0- 36 kg. Age range 0- 12 times. 

• Group 0 is for children importing 0- 13 kg. The baby auto seat is installed backward facing in the auto with Iso x connectors and the Top-Tether. The child is fastened with the 5- point belt of the baby auto seat. 

• Group 1 THis for children importing 9- 18 kg. The baby auto seat is forward facing and is attached to the auto with Iso x connectors and the Top-Tether. backward-facing use up to 18 kg with Iso x and Top- Tether is also permitted. The child is fastened with the 5- point belt of the baby auto seat. 

• Groups 2 and 3 are for children importing 15- 36 kg. The 5- point belt system of the child auto seat is removed. The child auto seat is directed forwards and is mounted on the auto via the Iso x connectors. The child is fastened by the 3- point belt of the auto. 

• It's recommended to install the auto seat on the hinder seat of the vehicle. For interior use in ECE Group 0/ 1, DO NOT attach the child seat to the frontal seat where there's an airbag unless the airbag can be killed. relate to the vehicle operating primer for further information. 

• This child auto seat is only suitable for vehicles equipped with Iso x connectors as well as 3- point safety belts according to ECE R16 or other original standards. The following table provides information about the fastening bias and styles of Baby First Ride

WARNING

 This is a ‘SEMI-UNIVERSAL ’ SAFETY RESTRAINT DEVICE FOR CHILDREN. It's tractable with   Regulation44/ 04 and may only be used in vehicles specified in the touching list of approved vehicles. 

• It can only be fitted on vehicles with 3- point safety belts, whether fixed or inertia-roll, compliant with UN/ ECE N ° 16 or an original standard. 

Notice regarding ISOFIX child restraint system( Group 0 I) 

 • This is an ISOFIX CHILD RESTRAINT SYSTEM. It's approved to Regulation No. 44, 04 series of amendments for general use in vehicles fitted with ISOFIX harbors systems. 

 • It will fit vehicles with positions approved as ISOFIX positions as detailed in the(vehicle textbook), depending on the order of the child seat and of the institution. 

 • The mass group and the ISOFIX size class for which this device is intended is Group I, B1 and Group 0 I, D 

 • Do not use this child seat at home. It has not been designed for home use and should only be used in your vehicle.

 • The safest seating position for this child seat is on the rear seat of a vehicle.

 • Never use the child seat without fastening the child’s harness correctly, and never attempt to use it without fastening into the vehicle.

 • Do not add to, or modify the seat in any way.

 • Do not leave your child unattended in the seat at any time.

 • Car interiors can become very hot when in direct sunlight, it is therefore recommended to cover the car seat when not in use. This prevents components,

• particularly those attached to the child seat becoming hot and burning the child. In the event  of an emergency, it is important that the child can be released

 • quickly. This means that the buckle is not fully tampered proof so your child must be taught never to play with the buckle.

CLEANING

This product has been designed with safety, comfort, and functionality in mind. Please take the time to read this manual carefully before using this product and keep it in a safe place for future reference. Do not use solvents, abrasive cleaners, or aggressive cleaning agents to ensure the long-term use of your child's car seat. Check the durability of the fabric and seams after each wash. When washing the fabric, follow the instructions on the label (see below) carefully.

• Wash at 30°C gentle cycle
• DO NOT iron
• DO NOT bleach
• DO NOT dry clean
• Drum drying at low temperature

MAINTENANCE

Regularly check the condition of the product for possible damage. In case of damage, do not use and keep out of the reach of children. 

SEAT PARTS

Front view, Rear view, Adjustable, headrest, Belt guide, (Group 2+3), Comfort insert, Belt buckle, Belt adjustment, Adjusting belt, Rotary lever, Shoulder pads U-bolt, Isofix connector, Seat shell, Shoulder pad, Shoulder belt, Lever for angle, adjustment, Headrest adjustment, Shoulder belt, Belt buckle, Isofix connector, extension, Rear facing Installation, Top-Tether belt guide, Buckle pad, Top-Tether belt, Sideprotector, Top-Tether adjuster

HOW TO USE OF THE CHILD NEO CAR SEAT

Adjusting the tilt angle of the car seat Use one hand to operate the angle adjustment lever on the lower front of the seat shell. The other hand holds the back of the seat shell and adjusts the angle.
When the child's car seat is used in the rearward facing direction, please use always the maximum reclining position In the forward-facing position (Group 1/2/3, 9-36 kg) the child's car seat can use all 3 reclining positions.
Rotation of the car seat Pull the lever at the front of the seat with one hand and turn the seat shell with the other hand. While the seat shell is rotating, the lever can be released.
There are 4 locking positions at 90, 180, 270, and 0/360° in the direction of the base. If the seat shell is in one of these positions, it is clicked into place.
The forward position (3-positions) is for children in groups 1, 2, and 3. The rearward position is for infants in groups 0+ and 1 (maximum angle) Forward facing only Rearward facing only

1. 90°
2. 270°
3. 0/360°
4. 180°

Adjustment of the belt

• To release the belt, press the red button of the front belt adjustment with one hand. With the other hand, hold the buckle with the straps attached and then loosen it.

• To fasten the belt, pull the front adjustment strap. Please pay every time attention to it, to adjust the belts so that they are on the same height as the children's shoulders.

Adjusting the headrest height

• Release the harness and pull the lever on the front of the headrest to the correct height to adjust the headrest.

•  Release the lever and make sure that the headrest is locked.

Opening/closing the belt

•  To unlock the harness, press the red button on the buckle and separate the two buckle tongues.

•  To lock the belt, first connect the 2 buckle tongues and then insert them together into the buckle.

Removing the belt systems

First press Strap adjuster. Then with the other hand, pull up the connection of the shoulder strap from the back of the Shell. (See below pictures) Remove the Strap from the connection of the shoulder strap and pull out the straps from the front of the car seat. So the headrest continues upwards to meet the taller children. Remove the two tongues of the buckle from the straps and insert them into the buckle slot. Then together with straps directly put into the place under the seat cover for storage.

Isofix connectors

•  Push the red insertion aids through the slot in the upholstery between the backrest and seat and into the Isofix brackets.

•  Make sure the flat side is facing down. This is not necessary if the vehicle already has fixed insertion aids.

•  Press both sides of the Isofix connector buttons to extend the Isofix connectors in length.

•  Insert the Isofix connectors into the insertion aids and press until you hear them click into place.

•  The display on both sides only turns green when the connections are made. Press the child's car seat against the backrest until it is secure. 

Top-Tether

•  Take the top tether out of the pocket.

•  To release the top tether, press the grey adjustment button with one hand and pull the side of the belt anchor to the required length with the other hand.

•  To attach the Top-Tether, attach the anchor to the attachment point on the car seat (pay} attention to top-tether routing for each group) and pull it as tightly as possible. The indicator does not turn green until the belt is locked.

INSTALLATION OF THE CHILD'S CAR SEAT

1) Group 0+ (rearward facing) (For children from 0-13 kg)

•  Press both sides of the Isofix connector buttons to extend the Isofix connectors in length.

•  Insert the Isofix connectors into the insertion aids and press until they click into place.

•  The display on both sides only turns green when the connections are made. Pull the child's car seat towards the backrest until it stands securely.

• Put the car seat into a maximum reclining position

• Rotate the seat into a rearward-facing position

• Take the Top-Tether out of the pocket.

•  To release the Top-Tether, press the grey adjustment button with one hand and pull the side of the belt anchor to the required length with the other hand.

•  Pull the upper belt through the belt guide marked blue on the seat.

•  Attach the anchor to the attachment point on the rear of the car seat.

•  Tighten the top tether by pulling on the other side of the strap. Make sure the indicator is green.

Group 1 (rearward facing)
(For children from 9-18 kg)

•  Press both sides of the Isofix connector buttons to extend the Isofix connectors in length.

•  Insert the Isofix connectors into the insertion aids and press until they click into place.

•  The display on both sides only turns green when the connections are made. Pull the child's car seat towards the backrest until it stands securely.

• Put the car seat into a maximum reclining position

• Rotate the seat into a rearward-facing position

• Take the Top-Tether out of the pocket.

•  To release the Top-Tether, press the grey adjustment button with one hand and pull the side of the belt anchor to the required length with the other hand.

•  Pull the upper belt through the belt guide on the headrest

•  Attach the anchor to the attachment point on the rear of the car seat.

•  Tighten the top tether by pulling on the other side of the strap. Make sure the indicator is green.

3) Group 1 (forward facing)
(For children from 9-18 kg)

•  Place the child's car seat on the car seat and rotate it to the forward-facing position.

•  Press both sides of the Isofix connector buttons to extend the Isofix connectors in length.

•  Insert the Isofix connectors into the insertion aids and press until you hear them click into place.

•  The display on both sides only turns green when the connections are made. Press the child's car seat against the backrest until it is secure.

4) Group 2/3 (forward facing)
(For children from 15-36 kg)

Remove the belt system as described in the previous point „Removing the belt systems“

•  Place the baby car seat on the car seat and place it in the forward-facing position.

•  Press both sides of the Isofix connector buttons to extend the Isofix connectors in length.

•  Insert the Isofix connectors into the insertion aids and press until they click into place.

•  The display on both sides only turns green when the connections are made. Pull the child's car seat towards the backrest until it stands securely.

• Place the child in the child's car seat.

•  Adjust the height of the headrest so that the red seatbelt guide under the headers remains free.

•  Guide the car‘s seat belt through the red belt guide under the headrest of the chill car seat.

•  Make sure that the lap belt runs through the side of the child's car seat.

•  Make sure that the lap belt in particular is tight and runs as low as possible over the child‘s pelvis.

•  Close the 3-point safety belt with the buckle on the car seat. Take care that the 3-point safety belt is not twisted.

•  Pull the vehicle‘s 3-point safety belt as tightly as possible and check that the child's car seat is securely positioned.